8051 microcontroller

Status
Not open for further replies.

Well, which cct did you use. Can you post or link to the schematic. Did you have diodes across the motor?
 
Actually, there were no diodes in it, i only had in my mind to give a fixed voltage supply to both the microcontoller and the motor used, and it had no diodes.
I had directly connected the motor to the microcontroller. pls help...
 
siva_elven said:
Actually, there were no diodes in it, i only had in my mind to give a fixed voltage supply to both the microcontoller and the motor used, and it had no diodes.
I had directly connected the motor to the microcontroller. pls help...
Click to expand...

You can't connect a motor directly to a microcontroller, particularly an 8051 which has very little current capability.

You need an H-bridge, and the size of it depends on the requirements of the motor.
 
Well i found a circuit rite now, it connects to the microcontroller via a L298 operating at 5 volts, i think it would suffice.
A L298 can be used instead of a h-bridge circuit, i hope so...
 
siva_elven said:
Well i found a circuit rite now, it connects to the microcontroller via a L298 operating at 5 volts, i think it would suffice.
A L298 can be used instead of a h-bridge circuit, i hope so...
Click to expand...

No, that will just provide drive current.
Did you actually look at any of those links I took the time to find for you?
 
Of course i did, and this is one of the circuits i got from there, i communicated there too, nd they sent me this ckt.
 

Attachments

  • untitled.PNG
    19.8 KB · Views: 979
  • powering up.JPG
    52.5 KB · Views: 994
siva_elven said:
Well i found a circuit rite now, it connects to the microcontroller via a L298 operating at 5 volts, i think it would suffice.
A L298 can be used instead of a h-bridge circuit, i hope so...
Click to expand...

Sorry! I read that as UNL2803 for some reason. Admittedly, I read hastily.

Yes, the L298 is designed for that. There is a circuit diagram on page 6 of the ST data sheet. It shows a motor connected using fast recovery diodes for protection.

The circuit you posted should work, but I would add the diodes.

Get the data sheet for yourself, and give it a go. Come back when you have it hooked up, or ...

EDIT: Just so it doesn't confuse you, the L298 is a dual h-bridge, and they are using the other one in each diagram.
 

Attachments

  • ST data sheet p5.gif
    20.4 KB · Views: 1,706
Last edited:
can i use a 89S52 in place of the 8051, nd use the same program as well, bcoz i read that 8952 is only an advanced version of 8051.
Pls suggest.
 
Download the datasheet and read the specs - but basically it's not a very powerful IC.

The motor current also won't be 1A, it will vary wildly, and during stall or heavy loads will be greatly higher than that.
 
well, i indeed think of connecting the diods between the L298 and the motor, but i dont know which diode, and how to connect it, pls, relate it to the circuit above and send a suitable connecton between the motor and the diode. nd pls suggest which diode to use.
 
i did download a datasheet of the ST electronics, but, i dont know whch ne, i looked it up, and i've got this diagram, just see it nd tell me whether this is the diagram or not.
 

Attachments

  • L298.JPG
    39.5 KB · Views: 686
siva_elven said:
i did download a datasheet of the ST electronics, but, i dont know whch ne, i looked it up, and i've got this diagram, just see it nd tell me whether this is the diagram or not.
Click to expand...

Looks like that is the correct data sheet, but that diagram is for stepper motors. It is on page 8, the one you want is on page 6. Look for the same diagram I posted... It is the same thing as what is shown in the circuit you posted, but with the diodes.
 
BeeBop said:
Should work well. For a diagram, look at the picture I posted from the data sheet. (You DID get yourself a data sheet, didn't you? )
Click to expand...
Actually schottkys should be used. The fast diode's 1.2V drop, if he is driving the rated current, is actually quite lossy and if the drop in the chip is lower helps very little if it is a synchronous rectifying chip.

Dan
 
Status
Not open for further replies.

Similar threads

D
  • Question
Chinese Prechin PZ51 tracker
Replies
2
Views
6K
Dan Kwon
D
C
HELP Assembly 8051 language
Replies
19
Views
10K
atferrari
K
  • Article
Gsm sim900 shield stopped working ||interfaced with 8051
Replies
0
Views
10K
koketso
K
T
  • Locked
8051 program
Replies
2
Views
9K
JimB
F
problem to understand how to divide two 16 bits number in 8051 microcontroller
Replies
1
Views
11K
rjenkinsgb
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…