Current reading

Status
Not open for further replies.
F

fixit7

Member
I have an Excel XL830 meter. When testing current, the scale is a bit confusing.

When set to the 2 ma scale, my reading showed .04 for the load used by the clock.

It uses lcds to display time,date,temp,and month day year.

Do I move my decimal to the right one place?

.04 or .4 ma ?

I need the value to calculate the run time when using 2 AA batteries.

I will use a capacity of 2200 Mah.
 
Without knowing the meter it's hard to say but I would guess 40mA as that is 0.04A. However, that makes no sense on a 2mA scale. What does it read on a 1A scale?

Mike.
 
Pommie said:
Without knowing the meter it's hard to say but I would guess 40mA as that is 0.04A. However, that makes no sense on a 2mA scale. What does it read on a 1A scale?

Mike.
Click to expand...

Seems fairly obviously 40uA - a 2mA range will actually be 1.999mA, it would be a VERY strange meter if it did differently.

And 40uA sounds about right for an LCD clock.
 
Instuctions for the meter are in Google:
1) Black probe in the COM jack.
2) Red probe in the V/Ohms/mA jack.
3) Set meter on the 20mA, 2mA or 200uA range.
4) Connect probes in series with battery and circuit. Hey, you cannot connect its probes in series with its own battery!

0.04mA is correct for an LCD clock. Then a 700mAh 9V battery lasts for 730 days.
If the reading is much too low then the 200mA fuse is blown or the battery is weak and the meter shows Low Batt.
A cheap Sooper Heavy Dooty Chinese 9V battery will last for about 1 day.
A Name Brand alkaline Western 9V battery will last for 730 days.
 

You do not get the gold star today.

As my post states, I am using 2 AA batteries not a 9V battery.

2200 mah / .04
------------------
24 hrs
= 2291 days = 6 yrs.

Does that sound reasonable? I am thinking that the current is .4 milliamps.

I read somewhere where those batteries should last around 2 years.
 
You are right. I checked a part with a listed current of under 18 ma.
It read 14.4.

Looks like my batteries will last around 6 years.
 
Remember that the simple meters insert a resistor, thus the voltage can also change. The drop is normally less than a diode drop of 0.7 V becaue diodes are used for protection. So, lets say 20 mV and 20 mA is a design goa, so a 1 ohm resistor is used. 20 mV being a displayed value/ Insertion at full scale will drop 20 mV. Check your meter specs.

ASIDE: I had a Harbor Freight $5.00 meter read 112 VAC on a telephone circuit with DSL to ground. I forget if it was tip to ground or ring to ground. One read 2.5 VAC and the other 112 VAC.

The meter read 120 VAC on a normal AC line. What's wrong? I put a DSO150 scope on it and found a 500 kHz signal on it, so I suppose the meter does not have an RFI filter on it.
 
The cheapo (7 bucks, free shipping from China on ebay) Chinese meter does not spec its "burden" voltage drop when measuring current.
2200mAh is fairly low for modern Western AA alkaline batteries. Energizer or Duracell AA alkaline cells would last their entire 10 years storage guarantee powering this clock.
 
I forgot that I have never purchased Duracell Alkaline cells because they leak. Duracell and Energizer Japanese Ni-MH cells are excellent.
 
I've had some Duracell batteries leak before the damn packet is even opened!
 
Mickster said:
I've had some Duracell batteries leak before the damn packet is even opened!
Click to expand...

Historically Duracell batteries NEVER leaked, and I've seen a LOT of leaking batteries over the years - however, a good many years ago now they obviously changed their construction because they became (and still remain) one of the biggest culprits for battery leakage.
 
Status
Not open for further replies.

Similar threads

D
  • Question
Fluke 123 scopemeter not reading ANY voltage, please help
Replies
4
Views
2K
Dickos
D
N
  • Question
Current draw from a Fridge compressor circuit
2
Replies
21
Views
4K
Nigel Goodwin
K
  • Question
BLDC Generator Back Current Protection
Replies
7
Views
3K
Tony Stewart
Test an AC Current Sensor Transformer
Replies
5
Views
3K
aliarifat794
A
T
  • Question
Even though it passes the diode test, I am unable to get any voltage reading from a 7805 voltage regulator while it is in a powered circuit.
Replies
4
Views
1K
techsleuth
T
Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…