Reporting bugs in the new siteware.

ElectroMaster · Sep 20, 2013

PG1995 said:
Hi

I was in process of writing a PM and had already written three-paragraph long message but then my computer crashed. Now I can recover only the first two lines of that message! In the past the auto-save for text editor was really good and it would save the content every few seconds and that's how I was able to retrieve the lost message content whenever my computer crashed without any problem and worry. It would be nice if the auto-save could save the content every few seconds again. Or, at least, please give us some way to save the content manually every few seconds. Thanks.

Regards
PG

The new site saves the messages at the same interval as the old. The interval is set to every 60 seconds.

ElectroMaster · Sep 20, 2013

PG1995 said:
Or, at least, please give us some way to save the content manually every few seconds. Thanks.

Look for the Drafts Button in the editor

PG1995 · Sep 20, 2013

Thank you, EM.

ElectroMaster said:
Look for the Drafts Button in the editor

But there is no Drafts button in the editor used for composing a PM!

Regards
PG

KeepItSimpleStupid · Sep 20, 2013

OK, nice and intuitive Thanks.

ElectroMaster · Sep 20, 2013

PG1995 said:
But there is no Drafts button in the editor used for composing a PM!

There should be one there..

PG1995 · Sep 21, 2013

Thank you, EM.

ElectroMaster said:
There should be one there..

Yes, there is one now. I believe you fixed it now or I was just too sleepy then!

Best wishes
PG

MrAl · Sep 22, 2013

Hi,

Talking about the timing related to posts, i've often wondered how long it takes for a message to actually get sent to the email address of the people who are 'subscribed' to the thread.

In other words, how long do we have to edit the material before it gets sent off to 1000 email addresses?

I wondered because i hate to see a hundred people get a message that reads:
"1+1=7.49384e-7"

because the poster did not type the correct result in the first draft
If we get five minutes to read over the draft we then have time to edit these typos.

jpanhalt · Sep 22, 2013

MOPPING UP

The fixes are coming along well. Here are a few items that caught my attention this morning:

The reply window cannot be dragged to make it bigger. It is like looking through a slit.
Under one's user name, there are several choices, such as Facebook Coordination and Blog drafts, but nothing to take the user to his/her blogs. There seems to be adequate space for that link. If needed, one could eliminate Facebook coordination or some other useless link.
"Banned" is now shown as a member category. I see no value in showing that. Can't the member category either be left blank or just Member."
Under the category of "planning ahead" Would it be possible to widen the space for characters or use a slightly smaller font for KISS?
Still no author on the Blog content page. Why not make the Blog content page just look like the Article with author information to the right?

John

ElectroMaster · Sep 22, 2013

Good List jpanhalt, I will be getting to them over the next week

tvtech · Sep 22, 2013

ElectroMaster said:
Good List jpanhalt, I will be getting to them over the next week

A hell of a lot of work you have put into the site to fine tune the Software EM. So far, all looks good. fantastic job.

One thing though...I need to PM Eric with photos from my PC.. Cant do it for now. A URL is required. And no URL is available as they were taken from my camera. And never on the Internet before. Concerns a little electronic project of mine.

Kind regards,
tvtech

jpanhalt · Sep 22, 2013

One thing though...I need to PM Eric with photos from my PC.. Cant do it for now. A URL is required. And no URL is available as they were taken from my camera. And never on the Internet before. Concerns a little electronic project of mine.

Assuming you have the pictures on your PC or can upload them to your PC, just click on the "Upload File" button at the bottom right, next to "Post Reply."

John

MikeMl · Sep 22, 2013

On the old software, I had it configured to display a forum thread with the newest post at the top. Can't find how to do that now...

Ian Rogers · Sep 23, 2013

MikeMl said:
On the old software, I had it configured to display a forum thread with the newest post at the top. Can't find how to do that now...

On "Your Profile" page click "Preferences" There is a combo box half way down...

MikeMl · Sep 23, 2013

Ian Rogers said:
On "Your Profile" page click "Preferences" There is a combo box half way down...

If you are talking about the attached menu, I have it checked, and it has no effect on how the forum thread is presented...

Ian Rogers · Sep 23, 2013

It must need fixing... I use the default so I never tried it.... I'll ask EM to comment...

Incidentally... Some changes don't take effect until you log out and back in again

ElectroMaster · Sep 23, 2013

If you're referring to Enable 'Newest Content', it is the content block on the home page to display the latest 10 posts, 5 blogs and articles. Unrelated to post order within threads.

There is no feature to display the newest posts first unfortunately.

jpanhalt · Sep 23, 2013

How do we reset our preferences to English? All of the pop-ups seem to be in Spanish.

John

killivolt · Sep 23, 2013

This is probably last on your list......https://www.electro-tech-online.com/posts/0/

I can't view it.

When you have time.

kv

Edit: This is what I was after on the main page.

spectrum analyzer for sale...Sep 5, 2013; longmanlee

tvtech · Sep 24, 2013

Hi All

Another thing I have noticed...our old v Bulletin ETO would require a person to Log in to view attachments. And user Profiles and so forth..

The xenForo software allows anybody access to anything. They just canno't post until logged in/signed up.

Check it out. Log out and simply visit again. ETO is at your disposal as an anonymous user. Hopefully this can be fixed.

Regards,
tvtech

tvtech · Sep 24, 2013

jpanhalt said:
How do we reset our preferences to English? All of the pop-ups seem to be in Spanish.
View attachment 80868 View attachment 80869

John

Hi John

Simplest is to change your browser to Firefox with Ad Block plus. You will never see another ad or pop up you have instructed Ad Block to....block. I have been here as a Member since 2010 and have yet to see any ads or pop-ups.

Regards,
tvtech

Reporting bugs in the new siteware.

Administrator

Administrator

Active Member

Well-Known Member

Administrator

Active Member

Well-Known Member

Well-Known Member

Administrator

Well-Known Member

Well-Known Member

Well-Known Member

User Extraordinaire

Well-Known Member

User Extraordinaire

Administrator

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads

Privacy & Transparency

Privacy & Transparency