Uart xc8 a little help formatting

while(1)
  {
     a = ADC_Read(0); //Reading Analog Channel 0
          USARTWrite(a);
          __delay_ms(1000); // 1 Second Delay
  }
}

void USARTWrite(char data)
{
  while(!TRMT);
  TXREG = data;
}

ca fb da da 00 fb db 58 de da

00 00 00 00 00 00 00 00 00

char str[6];
itoa(a,str,10);
i=0;
while(str[i])
     USARTWrite(str[i++]);
USARTWrite(',');

 while(1)
  {
     a = ADC_Read(0); //Reading Analog Channel 0
             char str[6];
     itoa(a,str,10);
     int i=0;
    while(str[i])
      USARTWrite(str[i++]);
      USARTWrite(',');
          __delay_ms(1000); // 1 Second Delay
  }
}

// Configuration Byte
#pragma config FOSC = HS        // Oscillator Selection bits (HS oscillator)
#pragma config WDTE = OFF       // Watchdog Timer Enable bit (WDT disabled)
#pragma config PWRTE = OFF      // Power-up Timer Enable bit (PWRT disabled)
#pragma config BOREN = ON       // Brown-out Reset Enable bit (BOR enabled)
#pragma config LVP = ON         // Low-Voltage (Single-Supply) In-Circuit Serial Programming Enable bit (RB3/PGM pin has PGM function; low-voltage programming enabled)
#pragma config CPD = OFF        // Data EEPROM Memory Code Protection bit (Data EEPROM code protection off)
#pragma config WRT = OFF        // Flash Program Memory Write Enable bits (Write protection off; all program memory may be written to by EECON control)
#pragma config CP = OFF         // Flash Program Memory Code Protection bit (Code protection off)
#include <xc.h>
#include <stdio.h>              // Standard I/O - required for printf() function
#include <stdlib.h>              // formatting text
#include "usart_pic16.h"
#define _XTAL_FREQ  20000000
void ADC_Init()
{
  ADCON0 = 0x41; //ADC Module Turned ON and Clock is selected
  ADCON1 = 0B10001111; //All pins as Analog Input
                 //With reference voltages VDD and VSS
}
unsigned int ADC_Read(unsigned char channel)
{
  if(channel > 7) //If Invalid channel selected
    return 0;     //Return 0
  ADCON0 &= 0xC5; //Clearing the Channel Selection Bits
  ADCON0 |= channel<<3; //Setting the required Bits
  __delay_ms(2); //Acquisition time to charge hold capacitor
  GO_nDONE = 1; //Initializes A/D Conversion
  while(GO_nDONE); //Wait for A/D Conversion to complete
  return ((ADRESH<<8)+ADRESL); //Returns Result
}
void main()
{
  //Initialize USART with baud rate 9600
  USARTInit(9600);
  TRISA = 0B00000001;
  ADC_Init();
  int a;
  while(1)
  {
     a = ADC_Read(0); //Reading Analog Channel 0
             char str[6];
     itoa(a,str,10);
     int i=0;
    while(str[i])
      USARTWrite(str[i++]);
      USARTWrite(',');
          __delay_ms(1000); // 1 Second Delay
  }
}

void  putch(char c)
   {
   USARTWrite(c);
   }

void main()
{
  //Initialize USART with baud rate 9600
  USARTInit(9600);
  TRISA = 0B00000001;
  ADC_Init();
  int c = 0;
  void  putch(char c)
   {
   USARTWrite(c);
   }
  printf("%d",ADC_Read(0));
       //__delay_ms(1000); // 1 Second Delay 
 // }
}