ltspice

Hello everyone, I have a question about LTspice for power electronics. how can I plot a parameter along the full simulation time, but it is averaged for each switching period? That is to say, Can I see this averaged value changes along the time? I know the .meas command can integrate between the...

How can i get current across voltage graph on LTSpice?

I'am trying to include BC237 diode from BC237.txt on LTSpice, but i have a trouble. I put the BC237.txt on the same directory that i am currently working. But it is not working. Can anyone help me?

Is there anyone can help me about that how can I put Vcc on the simulation? Thanks

How can i put the Vi's values on LTSpice? 30sin(2pi50t)

I have a complicated but linear component(its a coil with a certain shape of metal inside it) that I need to simulate with extreme accuracy. I can measure it's impedance and I would like to create an LTSpice component with that exact impedance so the simulation can be exact. is that possible? I...

Good afternoon, As the thread title suggests, I am having trouble simulating the UC3846 model in LTSPICE. I have gone through the process of creating the chip and adding it to the simulation space, but when configured in a similar way to the "Typical Application Diagram" from the data sheet it...

I starting a new thread now. I know how to get the power dissipation, taken the average value of the instaneous power with the thermometer probe over a component. But how come that the losses shows different each time? If I compare the circuit of an interleaved PFC and a boost PFC, where the...

Hello, I have designed a half-bridge DC/DC converter, but I am not not sure if this works properly. I asking cause the transformer is designed to give 380 V output (where the ratio is 7:14), but I only obtain around 277 V in the output of the converter.

Hello All, I need to find the absolute maximum peak value (not peak to peak) . It can be negative or positive. Now I am using the command .meas var tran max v(var) The command is working good but only for the positive side. I can use the min function but it will give me only the negative...

Do anyone have any suggestion how I can increase the efficiency for the LT1248 in LTspice? I have tried to change many parameters (the red circles) in the circuit according to the Data sheet, but it seems that nothing helps.. I always obtain the same output, about 500 W. --edit-- Is it possible...

Do anyone know how to check the THD (fft) in a easy way in LTspice? When I press the FFT-button, I got this window popping up. What should I select there? Maybe an alternative is to do this instead: I found somewhere that you need to write a SPICE directive like this: ".fourier {Freq}...

I know that it is possible to measure the power dissipation in LTspice according to this source: "To measure the wattage dissipation of a component , place the cursor on the components and press and hold down the ALT key, a thermometer cursor should appear. Read the Watts on the bottom screen...

Hello, What I understand it is possible to change the frequency externally by changing the components parameters, but I am not sure what to do to adjust the frequency. Can maybe someone show me how it will be implemented in the demo circuit? According to the data sheet, it says that "The...

I think the output current I get from the DC/DC converter is way too low, it should be at least 6-8 A, not in mA that I got. I think the resistor that I have in the end of the converter is needed in order to obtain 400 V. Do anyone have any suggestion what could be the problem? I found a...

Hi there, I need a suggestion how could I proceed, in Matlab simulink or Ltspice, , mathematically I have managed all factors and formulas, In a permanent magnet synchronous motor where inductances vary as a function of rotor angle, the 2 phase (d-q) equivalent circuit model is commonly used...

Hello everyone. I'm trying to simulate a classic regenerative receiver under LTSpice. I'm not sure if I'm doing things correctly. I'd appreciate if anyone could correct me if I'm wrong, or suggets better ways of doing it. I modeled the antenna as a voltage source. Of course it is NOT real. I...

Hello, I trying to find a equivalent battery model for a PHEV (plug-in-electric vehicle) and simulate the charing process in LTspice. I want the battery to have SOC=0, an empty battery from the begining, and starts to charge between the charging range of 320-380 V. I know the battery should...

I'm working on a project involving the simulation of NTC thermistors both in LTSpice and my own optimization scripts in Matlab. In the process of debugging, I noticed that LTSpice was producing unexpected behavior for a circuit I'd put together. The circuit in question is a thermal anemometer...

I need to overlap the MC gaussian distribution for threshold voltage generated using MATLAB and LTspice..If i use the same mean value(i.e 0.3558) and sigma value(3*sigma=10% i.e sigma=0.0333) for both my simulations then MATLAB distribution is much more wider than LTspice distribution..On the...

Hi there, I am Talgat. I am doing some revision work with LTSpice. I wanted to ask experienced members, how to "draw DC transfer characteristics of an AC sinusoidal current source with an amplitude of 1V and 50Hz".

I am having trouble getting LTSpice to simulate oscillations. I drew a schematic of a simple DC source and resistor circuit to make sure I could get the software to work, and after running and adding a current waveform, the waveform displayed just as it should. Then, I tried two oscillators: a...

I m trying to simulate an inverter using LTSpice..I m using 32nm PTM technology..I want the delay to be a gaussian PDF..May i know whats wrong with the .asc file attached below.

In my quest to design my own an audio power amplifier, I'm trying to fully understand how to design a proper BJT differential amplifier. I faced two apparently easy questions I cannot answer by myself, even after some hours of thinking about it. First is about long-tailed pair using resistive...

I have created the netlist file filename.net in matlab. When i try to run the netlist file in matlab or in ltspice, I get 'Encountered a sharing violation while accessing a filename.net file' error message. If I terminate matlab and run netlist file in ltpsice or by double click, it will run...