3x3x3 LED Cube - can i use16f628 instead 16f690

birdman0_o · Nov 23, 2009

Is your led #9 connected to pin RA4? If it is...you should probably a) use a translator b) go to a forum of your language....

turker · Nov 23, 2009

birdman0_o said:
Is your led #9 connected to pin RA4? If it is...you should probably a) use a translator b) go to a forum of your language....

yeah..my led is 9 connected to pin RA4..

Number17 · Nov 23, 2009

RA4/T0CKI/CMP2 RA4 ST OD Bidirectional I/O port. Output is open drain type.
T0CKI ST — External clock input for TMR0 or comparator output
CMP2 — OD Comparator 2 output

This is from the datasheet. You need to connect the led from 5v to RA4 or add a transistor/buffer like birdman already said

kssoin · Nov 30, 2009

Hello All on this thread,
I am just staring on this project. after going through this thread i thought of getting the schematic cleared from you. I will use pic16F628A.
Port B will be used for the eight LEDS on each layer(RB0 to RB7).
RA0 for top layer common point.
RA1 for middle layer common point.
RA2 for the bottom Layer common point.
and RA3 for the ninth LED on each layer.
Please let me know if this setup ok.
Will the code need any change?
Regards.
kssoin

turker · Nov 30, 2009

kssoin said:
Hello All on this thread,
I am just staring on this project. after going through this thread i thought of getting the schematic cleared from you. I will use pic16F628A.
Port B will be used for the eight LEDS on each layer(RB0 to RB7).
RA0 for top layer common point.
RA1 for middle layer common point.
RA2 for the bottom Layer common point.
and RA3 for the ninth LED on each layer.
Please let me know if this setup ok.
Will the code need any change?
Regards.
kssoin

thank u very much..i'm cheking my code..

sahu · Dec 4, 2009

any body can provide right code & right ckt dia. 3x3x3 cube 16f628a.

birdman0_o · Dec 4, 2009

If you even bothered to look at the other posts you would see it's already here

sahu · Dec 4, 2009

birdman0_o said:
If you even bothered to look at the other posts you would see it's already here

pl clear it.which asm code & ckt dia. is 100% tested with u .
MY ENG. POOR PL DON'T MIND

sahu · Dec 4, 2009

turker said:
thank u very much..i'm cheking my code..

ofter cheking ur code. I req. U pl share hear .

be80be · Dec 4, 2009

The right one may not be on here It was but some one ask how to use this on a motor bike and I re posted it for them with the same name its not that hard to change

hook 8 of the columns to portB and column 9 to portA 3
then the rows are porta 5 6 7

birdman0_o · Dec 4, 2009

Your too kind bebe, these people put in no effort whatsoever, and you still help them out

sahu · Dec 5, 2009

be80be said:
The right one may not be on here It was but some one ask how to use this on a motor bike and I re posted it for them with the same name its not that hard to change

hook 8 of the columns to portB and column 9 to portA 3
then the rows are porta 5 6 7

thank u mr. be80be. to day will chek it

birdman0_o · Dec 5, 2009

It would be nice for somebody to post finished pictures of the cube. So if you get it working on the 16f628a sahu please post your finished project.

sahu · Dec 5, 2009

birdman0_o said:
It would be nice for somebody to post finished pictures of the cube. So if you get it working on the 16f628a sahu please post your finished project.

OK

be80be · Dec 5, 2009

This is with a 16f628a
[embed]http://www.youtube.com/v/OsUJwhyjJJc&hl=en_US&fs=1&[/embed]

Sceadwian · Dec 5, 2009

Nice, but I've always thought these kinds of LED cubes would look a whole lot better if SMD LED's were used because the package size is so much smaller there's a lot less to get in the way of the eye.

birdman0_o · Dec 5, 2009

Awesome thanks bebe

sahu · Dec 9, 2009

3x3x6 led cube

be80be said:
The right one may not be on here It was but some one ask how to use this on a motor bike and I re posted it for them with the same name its not that hard to change

hook 8 of the columns to portB and column 9 to portA 3
then the rows are porta 5 6 7

mr. be80be,how can exentend it 3x3x6 led cube. becose 3s pin not used in this project .so i want used it for exetend [6] layer.

be80be · Dec 9, 2009

A 3x3x6 would take 3 more output pins you could added them but you will need a bigger chip like the 16f877 or 16f876
And you'll need drivers for leds

sahu · Dec 9, 2009

be80be said:
A 3x3x6 would take 3 more output pins you could added them but you will need a bigger chip like the 16f877 or 16f876
And you'll need drivers for leds

no sir extualy [ hook 8 of the columns to portB and column 9 to portA 3
then the rows are porta 5 6 7].means we use three rows. but i want six rows.

3x3x3 LED Cube - can i use16f628 instead 16f690

Active Member

New Member

New Member

New Member

Attachments

New Member

Member

Active Member

Member

Member

Well-Known Member

Attachments

Active Member

Member

Active Member

Member

Well-Known Member

Banned

Active Member

Member

Well-Known Member

Member

Similar threads

Privacy & Transparency

Privacy & Transparency